First, the common reasons for rust:
1. After the operation (after use), the instrument is not pre-cleaned or the pre-cleaning is not complete, resulting in the appearance of the attached material being too long, and then corrosion induces rust;
2. Misuse (concentration and soaking time) rust remover, 84, effervescent tablets and other consumables cause the device to be corroded, which in turn induces rust;
3. The surface lubrication concentration is too low, the surface lubrication is not in place, resulting in collisional orientation damage, and then induced rust;
4. The rust removal method is not correct, the rust is not completely removed, causing the rust to grow and expand;
5. Using wire brush, copper wire brush, steel ball, scouring pad and other scouring equipment, destroying the outer protective layer of the instrument and losing the function of rust prevention;
6. New equipment is mixed into most rusty old equipment and used for infection;
7. There are too many rust particles in the sterilized steam.
Second, preventive measures:
1. The contact of the device with chloride should be minimized throughout the application and reprocessing process;
2. After the operation, the device should be washed with running tap water in time, and ensure the quality of the flushing. It should not be wiped with salt water and sent to the supply room in time.
3. Devices that cannot be transported in a timely manner (more than 8 hours), overnight, and holidays should be moisturized with a special moisturizer for foam;
4. The decontamination area of ​​the supply room should be pre-cleaned by hand. There should be no residue visible to the naked eye, and then it can enter the automatic cleaning machine or the ultrasonic cleaning machine. The joints are opened and placed in an appropriate amount to ensure the cleaning quality.
5. For rusted equipment, the correct rust removal method should be used to remove rust and ensure complete rust removal;
6. It is strictly forbidden to use 84, effervescent tablets and other chlorine-containing disinfectant for long-term immersion disinfection equipment, soaking concentration in strict accordance with the standard;
7. When cleaning the device, the smoothing agent should be placed at the correct dosage, the joints should be worn or worn, or the area should be rusted. If necessary, spray smoothing agent should be used for secondary lubrication;
8. Before sterilization and packaging, it must be strictly observed. If necessary, use a magnifying glass with light source. The equipment with rust can not be packaged and sterilized!
1. After the operation (after use), the instrument is not pre-cleaned or the pre-cleaning is not complete, resulting in the appearance of the attached material being too long, and then corrosion induces rust;
2. Misuse (concentration and soaking time) rust remover, 84, effervescent tablets and other consumables cause the device to be corroded, which in turn induces rust;
3. The surface lubrication concentration is too low, the surface lubrication is not in place, resulting in collisional orientation damage, and then induced rust;
4. The rust removal method is not correct, the rust is not completely removed, causing the rust to grow and expand;
5. Using wire brush, copper wire brush, steel ball, scouring pad and other scouring equipment, destroying the outer protective layer of the instrument and losing the function of rust prevention;
6. New equipment is mixed into most rusty old equipment and used for infection;
7. There are too many rust particles in the sterilized steam.
Second, preventive measures:
1. The contact of the device with chloride should be minimized throughout the application and reprocessing process;
2. After the operation, the device should be washed with running tap water in time, and ensure the quality of the flushing. It should not be wiped with salt water and sent to the supply room in time.
3. Devices that cannot be transported in a timely manner (more than 8 hours), overnight, and holidays should be moisturized with a special moisturizer for foam;
4. The decontamination area of ​​the supply room should be pre-cleaned by hand. There should be no residue visible to the naked eye, and then it can enter the automatic cleaning machine or the ultrasonic cleaning machine. The joints are opened and placed in an appropriate amount to ensure the cleaning quality.
5. For rusted equipment, the correct rust removal method should be used to remove rust and ensure complete rust removal;
6. It is strictly forbidden to use 84, effervescent tablets and other chlorine-containing disinfectant for long-term immersion disinfection equipment, soaking concentration in strict accordance with the standard;
7. When cleaning the device, the smoothing agent should be placed at the correct dosage, the joints should be worn or worn, or the area should be rusted. If necessary, spray smoothing agent should be used for secondary lubrication;
8. Before sterilization and packaging, it must be strictly observed. If necessary, use a magnifying glass with light source. The equipment with rust can not be packaged and sterilized!
Non-Locking Plate,Non-Locking Orthopedic Plate,Titanium Olecranon Plates,Humerus Distal Plates
Medton Medical , https://www.medton.cn